NEWS
Position:
Homepage
/
/
How to install and disassemble the inflatable boat?

How to install and disassemble the inflatable boat?

  • Categories:News
  • Author:
  • Origin:
  • Time of issue:2021-06-16
  • Views:0

(Summary description)Before installing or disassembling the rubber boat, first clean up the nearby hard objects, then open and lay the boat flat. The best temperature is 15.5℃. The spring rod of the check valve should be closed, counterclockwise until the spring rod is convex. (Note: close the valve before inflating, the safety valve will automatically vent when inflated too much to protect the inflatable boat), then use the air pump to fill the center keel with air to support the skeleton, and then use Foot pump or use an electric pump with adjustable air pressure and switch to inflate the hull.

How to install and disassemble the inflatable boat?

(Summary description)Before installing or disassembling the rubber boat, first clean up the nearby hard objects, then open and lay the boat flat. The best temperature is 15.5℃. The spring rod of the check valve should be closed, counterclockwise until the spring rod is convex. (Note: close the valve before inflating, the safety valve will automatically vent when inflated too much to protect the inflatable boat), then use the air pump to fill the center keel with air to support the skeleton, and then use Foot pump or use an electric pump with adjustable air pressure and switch to inflate the hull.

  • Categories:News
  • Author:
  • Origin:
  • Time of issue:2021-06-16
  • Views:0
Information

Before installing or disassembling the rubber boat, first clean up the nearby hard objects, then open and lay the boat flat. The best temperature is 15.5℃. The spring rod of the check valve should be closed, counterclockwise until the spring rod is convex. (Note: close the valve before inflating, the safety valve will automatically vent when inflated too much to protect the inflatable boat), then use the air pump to fill the center keel with air to support the skeleton, and then use Foot pump or use an electric pump with adjustable air pressure and switch to inflate the hull. It must be inflated according to the rated air pressure in the factory manual (Note: compressed air pump cannot be used to inflate, such as a car tire pump. Over-inflation will damage the seams of the inflatable boat. Waterproof membrane), the installation of the seat depends on the design of the inflatable boat. Generally, when the hull is half inflated, the two sides of the seat board should be clamped on both sides of the hull, and then the hull is filled with air. After all the air chambers of the hull are filled with gas, connect the oars and install them on the boat. Refer to the instructions for specific installation.

When disassembling the inflatable boat, pay attention to the cleanness and dryness of the hull, then open all valves and press down the spring lever and lock it in a clockwise direction. If it is an aluminum pedal bottom, first remove the aluminum bracket and middle pedal before dismantling the bow. After squeezing the ship’s hull and stern board, first squeeze the ship’s hull to release part of the air, then use a foot pump to extract all the air in the ship’s air storage pipes. Fold the bow to the stern, put it in a carrying bag, store the hull in a clean and dry place, avoid direct sunlight, and be careful of small animals (such as kittens) damage the hull.

Be careful when cleaning the inflatable boat. Do not use wax, vinyl solvents, chemicals, chlorine, alcohol-containing cleaners and gasoline to clean the hull. All hulls can be cleaned with soap and water. The PVC cloth has been anti-ultraviolet before leaving the factory. Light coating, such as spraying anti-ultraviolet agent once every six months on the whole ship (available in marine supply stores), can increase the life of the inflatable boat.

1

Scan the QR code to read on your phone

16 2021-06
Corporate News
How to choose a surfboard that suits you
Classification of surfboards Below 7 feet (excluding 7 feet) is called a shortboard. 1 foot is equal to 30 cm. 9 feet (feet) includes 9 feet or more to become a longboard (longboard).
16 2021-06
Corporate News
What is the difference between an inflatable kayak and an inflatable boat
It can be said that apart from the water supplies, kayaks and inflatable boats are very different. If you want to buy an inflatable boat, you will be very funny if you buy a kayak back. The following is the analysis of the difference between kayaking and inflatable boat by Haiweilong rubber boat;
16 2021-06
Corporate News
Assault boat | repair methods for damaged rubber boats
Each assault boat | assault boat | inflatable boat is equipped with a repair kit to repair small damages. Through use, your yacht may appear the following small
16 2021-06
Corporate News
Assault boat | inflatable boat service life
(1) The main factor that affects the life of the assault boat | inflatable boat is ultraviolet light, so the main means to extend the life is to prevent ultraviolet light.

MESSAGE

留言应用名称:
客户留言
描述:
验证码

CONTACT US

Copyright ©  Shandong M&H Outdoor Co., Ltd    鲁ICP备2021023196号      Powered by www.300.cn  |  SEO